The Dude

What's new in this version:

- arm64 - allow enabling receive packet steering on /system/resource/irq/rps menu in order to overcome unbalanced CPU load
- bgp - allow duplicate router-ids for eBGP sessions (RFC 6286)
- bgp - always advertise extended nexthop cap for all supported address families
- bgp - do not allow iBGP with non-equal ASNs
- bgp - fixed l2vpn-cisco decoding (introduced in v7.20)
- bgp - fixed occasional corruption of MPLS labels in BGP VPN update messages
- bgp - fixed route refresh subcode 0 warning
- bgp - fixed selection of received BGP VPN routes
- bgp - implement RFC 9234 route leak prevention and detection using roles
- bonding - added lacp-system-id and lacp-system-priority settings
- bonding - fixed lacp-mode=passive
- bonding - improved stability for 802.3ad LACP
- bridge - expose more DHCP snooping warning logs
- bridge - fixed dynamic switch-cpu VLAN creation (introduced in v7.20)
- bridge - fixed filter and NAT matching with "mac-protocol=length"
- bridge - fixed missing local MAC after changing protocol-mode setting
- bridge - fixed multicast packet receiving on bridge as multicast-router when HW offloading is used
- bridge - fixed possible DHCP packet drop caused by the add-dhcp-option82
- bridge - fixed possible MVRP issues when STP topology changes
- bridge - fixed static host and MDB entry updates on VLAN add/remove
- bridge - improved DHCP Option 82 values (circuit-id:"interface-name:vid", remote-id:"bridge MAC address")
- bridge - improved stability after failed protocol-mode=mstp change
- bridge - improved system stability when forwarding traffic with fast-path and bridged interface gets removed or disabled (introduced in v7.20)
- bridge - properly apply bridge MVRP settings on the fly
- bth - added file-share link preview
- bth - fixed big file upload
- bth - fixed file-share expire after reboot
- bth - make user private-key sensitive
- certificate - added certificate "trust-store" parameter
- certificate - added option to configure built-in trust store (replaced "builtin-trust-anchors" parameter)
- certificate - added SHA384, SHA512 support for SCEP
- certificate - allow ca-crl-host parameter for issued certificates
- certificate - fixed incorrect appearance of "invalid-before" and "invalid-after" dates
- certificate - improved logging
- certificate - on certificate import, added the "issued" flag if the certificate store contains the imported certificate's CA and its private key
- certificate - refactored Certificate internal processes
- chr - fixed guest OS type "Other Linux (64-bit)"
- console - added "mvrp" to mac-protocol setting
- console - added delimiter parameter to :toarray command
- console - added fetch-changelog flag to check-for-updates command
- console - added reset command to settings directories
- console - added sensitive flag to QR code in WireGuard "show-client-config"
- console - added show-sensitive option for print command, hide sensitive settings in print output by default
- console - changed file id format
- console - do not allow to set value as empty for arguments that require selection of a specific list entry
- console - do not set values when "setup" command is interrupted
- console - fixed :convert from=num on MIPSBE
- console - fixed "special-login" setting incorrect channel
- console - fixed autocomplete in fullscreen editor to append tabs, spaces, etc
- console - fixed empty output in route menus when using "print where gateway"
- console - improved :toip command to get IPv4 address from IPv4 CIDR address
- console - improved :toip6 command to get IPv6 addresses from IPv6 prefixes
- console - improved hints for address arguments
- console - improved hints for DHCPv6
- console - improved printing visuals (column layout and paging)
- console - improved stability
- console - remove unnecessary commands from /ip/hotspot/active menu
- console - removed /quickset menu
- console - return error values for certain commands if action failed (e.g. /system/routerboard/upgrade)
- console - show fullscreen script editor completions above hintbar
- console - updated "Change your password" to "Change your password (Ctrl-C to skip)"
- console - updated copyright notice
- container - add initial Bluetooth device support
- container - added "/app" menu for simple containerized app installation (requires "container" package and enabled "container" device-mode)
- container - added CPU usage
- container - added hosts setting
- container - added kill command to send signals (CLI only)
- container - added option to limit CPUs used by containers
- container - added root dir size
- container - added run command to allow interactive mode (CLI only)
- container - added stop-time setting
- container - added update command (CLI only)
- container - allow /tmp tmpfs to be unlimited in size
- container - allow app network to be any bridge interface
- container - allow to configure extra ENV variables directly in container
- container - allow to disable/enable envs and mounts
- container - allow to specify mounts directly in container
- container - calculate volume sizes
- container - convert container mounts setting to mountlists, old mount name becomes list name, list name can map to multiple mounts
- container - do not allow layer-dir to be within some containers root-dir
- container - enable relevant kernel features to support more container apps
- container - fixed error for starting container which consists of large number of layers
- container - fixed extract issues
- container - fixed VETH when using long interface name
- container - general container service stability fixes and improvements
- container - have per container layer-dir setting to be able to have separate layer stores for different sets of containers
- container - made it possible to set timeout on /container/shell
- container - make sure a working directory is created if it does not exist
- container - show detailed import status, helps understand long imports
- container - show image-id field (CLI only)
- container - shows app URL and "running" status only when port is open
- container - store image import data (allows keeping container after netinstall)
- detnet - do not try detection on slave interfaces
- detnet - fixed unnecessary process starting even when feature is not enabled
- dhcpv4-client - don't stop client on unsuccessful client option value change
- dhcpv4-server - added "support-broadband-tr101" setting to pass additional Option 82 suboptions to RADIUS server
- dhcpv4-server - added setting allowing to select client-id, MAC address and opt82 parameters for dynamic lease addition
- dhcpv4-server - allow creating static DHCPv4 leases for VETH interfaces
- dhcpv4-server - allow to set other gateway types not just IP for dhcp lease "routes" parameter
- dhcpv4-server - improved logging
- dhcpv4-server - improved setup wizard prompts relating to DNS
- dhcpv4-server - respond with hlen 0 when htype is 8
- dhcpv4-server - send RADIUS Accounting Stop messages when interim-update is zero
- dhcpv6-client - do not show I flag for disabled client
- dhcpv6-client - fixed misleading "couldn't acquire address, continue with prefix only" error when prefix is not even requested
- dhcpv6-relay - added "about" error message option
- dhcpv6-relay - enable configuration of options that are added to relayed DHCPv6 requests
- dhcpv6-server - added accounting to use-radius setting, similar to DHCPv4 server
- dhcpv6-server - attempt to extract MAC from DUID for dual-stack purposes when client uses DUID-EN type of DUID
- dhcpv6-server - improved event logging messages
- dhcpv6-server - improved service stability when receiving DHCP requests for PPP service clients without included IA_PD
- dhcpv6-server - include traffic usage statistics when accounting is stopped due to binding expiry and removal
- discovery - correctly report PoE dual signature per-pair class
- discovery - fixed MNDP IPv6 status reporting
- discovery - send out neighbor discovery immediately on IPv4/IPv6 changes
- disk - added nvme-tcp-server-nqn setting to be able to explicitly configure NQN, will default to "nqn.2000-02.com.mikrotik:slot" for new configurations
- disk - allow only lowercase chars in iscsi-server-iqn
- disk - allow to have type=file devices without rose-storage (needed for file based swap)
- disk - allow to set smb-share only for type=smb
- disk - consolidate client states into single field, as each item can be only one type of "client"
- disk - do not allow setting raid-master when have filesystem
- disk - do not allow starting Btrfs replace when replace is suspended
- disk - do not delete partition configs on device remove and eject (fixes lost config with unstable hardware)
- disk - fixed iscsi client
- disk - fixed iscsi export disable
- disk - fixed issue with double "/" in SMB share path for some clients
- disk - fixed SATA eject/scan
- disk - fixed SMB mount to be writable by container
- disk - fixed write RAID superblock
- disk - improved cleanup order to avoid waiting for timeouts on shutdown
- disk - improved RDS2216 SATA controller
- disk - improved system stability
- disk - rename nvme-tcp client name to nqn everywhere symmetrically with server
- disk - show NVMe critical warnings
- disk - unshare iscsi and nfs client/server ids, add iscsi-server-iqn
- disk - update interface type/speed after scan
- disk - use default label when nothing specified when formatting from WinBox
- dns - added VRF support to ":resolve" command
- dns - added VRF support to DNS servers
- email - added "certificate-verification" parameter
- email - return all errors to console when executed from console
- eoipv6,gre6,ipip6 - added "dont-fragment" setting to control packet fragmentation for packet sizes exceeding underlay interface MTU
- ethernet - added "unsupported speed" warning for forced 1Gbps, 2.5Gbps, 5Gbps, 10Gbps baseT modes
- ethernet - change default L2MTU 1518 to 1596 for RB5009
- ethernet - fixed 2.5G-baseT link-partner-advertising on RB5009, hAP ax3, Chateau ax devices
- ethernet - improved Ethernet port mapping to ensure a consistent and reliable interface order for wAP ax
- ethernet - improved system stability for RB912, RB911 devices
- evpn - fixed Ethernet Segment (ES) routes
- fetch - added "http-percent-encoding" parameter
- fetch - fixed http headers appearance when received payload is empty
- fetch - send http-data for any http method
- file - distinguish empty mount points from disks
- file - improved error messages provided to GUI
- file - improved stability and interoperability with WinBox and console
- firewall - added "h" flag indicating that firewall service helper is applied for particular connection
- firewall - added support for TOS/mask matching for raw rules
- firewall - clear relevant masqueraded connection tracking entries on IP address change
- firewall - fixed "tls-host" not matching expected hosts
- firewall - fixed hotspot value loss on rule enable/disable
- firewall - fixed strip-ipv4-options always passthrough
- firewall - hide hw-offload setting from devices that do not support it
- firewall - improved system stability and memory allocation when using firewall services
- firewall - make hw-offload=yes default setting in /ip/firewall/filter menu
- firewall - use the highest TTL as timeout value for domain address list entries if multiple domain names resolve to same IP
- health - upgraded fan controller firmware to latest version
- hotspot - added TOTP support for local hotspot users
- hotspot - improved system stability
- hotspot - prevent service from starting unnecessarily in the background on export/print commands
- ike2 - adapt rekey procedure for compatibility with Libreswan
- iot - added LoRa Round Trip Time monitoring support
- iot - added Modbus rx-switch-offset parameter which helps offset Rx window
- iot - added mqtt disconnect/connect GUI options
- iot - added support for Modbus port baud-rates from 9600 to 115200
- iot - changed LoRa packet's timestamp format, which fixes duty cycle issues for some servers
- iot - improved Modbus multi-write registers handling
- ip-service - do not duplicate entries for containers running in same netns
- ip-settings - limit IPv4/IPv6 max-neighbor-entries maximum value
- ippool6 - added "Valid Lifetime" and "Preferred Lifetime" options and use them when constructing IPv6 address
- ippool6 - fixed minor memory leak
- ippool6 - log address removal
- ippool6 - take into account "subnet-id" when specified on address
- ipsec - fixed CHACHA20 typo in log messages
- ipsec - support Post-Quantum Pre-shared Key (PPK) with QKD integration (CLI only)
- ipv6 - added "none" option for IPv6/ND/Prefix when advertising just options, not prefix
- ipv6 - added "self" option for IPv6/ND DNS advertise settings
- ipv6 - allow to specify on which interfaces to accept Router-Advertisements
- ipv6 - do not disable/enable Router-Advertisements functionality based on IPv6/ND configuration
- ipv6 - initialize RA receiving when enabled and without any other IPv6 configuration
- ipv6 - properly remove SLAAC installed route when prefixes expire
- ipv6 - remove SLAAC installed DNS server and route on expire
- isis - improved stability
- isis - improved system stability when changing passive flag
- isis - improved system stability when receiving a hello packet
- l3hw - added per-VLAN "l3-hw-offloading" setting and "H" flag for /interface/vlan menu
- l3hw - display warning when partial offloading is active (suggest users to use suppress-hw-offloading to control which routes get HW offloaded and which are CPU processed)
- l3hw - fixed issue with IPv4 ARP and IPv6 neighbor resolve for CRS812
- l3hw - fixed partial offloading with /31 routes
- l3hw - fixed per-VLAN counters when packets are going through CPU
- l3hw - fixed VLAN and VXLAN counters for CRS520 device
- l3hw - improved stability and performance during L3HW enable with many routes
- l3hw - improvements and optimizations for IPv4 /32 and IPv6 /128 route offloading
- l3hw - prioritize local IP address over ARP/neighbor entry with same IP (fixes incorrect packet flow)
- log - fixed ISO8601 time format
- log - fixed memory leak
- log - fixed remote logging on remote-protocol configuration change
- log - fixed unnecessary file creation when configuring a disabled log action with "target=disk"
- log - hide irrelevant log action parameters
- log - limit firewall log prefix length
- log - limit log socket buffer memory size
- lte - added "force-delete" command to allow deletion of active eSIM profiles
- lte - added additional logging for error reported by modem during APN profile setup
- lte - added command to send out EUICC generated notifications manually
- lte - added confirmation prompt when deleting eSIM profile
- lte - added support for additional D-Link DWM-222 variation (vendor-id="0x2001" device-id="0x7e46")
- lte - added support for additional Huawei E3372-325 variation (vendor-id="0x3566" device-id="0x2001")
- lte - added support for R11e-LTE6 v039 firmware release and availability notification
- lte - ask for user confirmation before installing eSIM profile
- lte - clear SIM not present error when performing modem FW upgrade
- lte - discontinued support for RBSXTLTE3-7, further versions will use v7.20 LTE firmware package
- lte - do not retry activation for IPv4 and IPv6 APNs on QMI modems if only one address family is assigned
- lte - fixed cases where LTE monitor could show abnormalities
- lte - fixed LTE interface IPv6 address generation to use EUI-64 (introduced in v7.20)
- lte - fixed MTU inheritance from master interface in multi-APN setups
- lte - fixed MTU setting for AT modems
- lte - fixed no re-connection after cellular network requested APN deactivation on Chateau 5G ax R17
- lte - force sms-protocol to AT for FG621-EA modem
- lte - improved AT modems at-chat control channel handling after modem has closed AT channel unexpectedly
- lte - improved modem recovery for Chateau 5G and Chateau 5G R16
- lte - improved stability for FG621-EA modem
- lte - improved system stability when receiving SMS messages
- lte - provide firmware download URL when no LTE package installed on "SXT LTE3-7"
- lte - relay EUICC generated notifications after profile enable/disable/remove/provision
- lte - rework multiapn support for AT modems
- lte - unify "SIM not present" status for all modems
- macsec - added initial support for hardware-offloaded support (available only on QCA8081 PHY: RB5009, hAP ax3, Chateau ax ether1 port)
- media - fixed console autocomplete for path parameter
- mpls - fixed LDP filter upgrade from v6 where neighbor parameter is not specified
- mpls - fixed update of LDP Address message when local addresses change
- mpls - properly renew services when LDP transport address changes its state
- netinstall - fixed install with old RouterBOOT
- ospf - changed nssa-translator default value from no to candidate
- ospf - fixed OSPF interface "Standby" state detection
- ospf - improved stability
- ospf - show interface as separate prop for interface and neighbor
- ovpn - fixed OVPN server handling on reboot (introduced in v7.20)
- ovpn - improved system stability when using cipher=blowfish128
- ovpn-server - added support for pushing IPv6 routes
- poe-out - added input name hint to poe max-power settings
- poe-out - added LED blink on error for RB5009
- poe-out - firmware update for 802.3at capable boards (the update will cause brief power interruption to poe-out interfaces)
- poe-out - fixed CRS354 misreporting approved LLDP power
- poe-out - improved firmware update stability
- poe-out - improved power-on mechanism for 802.3at capable boards
- port - added comment for /port/remote-access (CLI only)
- port - added support for additional baudrates for USB to serial adapters
- port - do not show serial port for ATL 5G R16
- port - fixed displaying "baud-rate=auto" on x86
- port - fixed export for default serial port name
- port - give "gps" prefix for R11e-LR8G and R11e-LR9G GPS ports
- ppp - added multi-APN support to ppp-client dialer
- ppp - added setting to set BG77 modem cellular connection mode (auto; lte-m; nb-iot) (CLI only)
- ppp - improved service stability when using IPv6 with DHCP and RADIUS accounting
- qos-hw - added "default" flags to default entries
- qos-hw - added "mirror-profile" which allows to select profile (traffic-class) for mirrored traffic
- qos-hw - always show usage and PFC counters, even when they are zero
- qos-hw - fixed counters for ports that are configured with "offline" tx-manager
- qos-hw - fixed profile add/remove for CRS812
- qos-hw - fixed shared-pools for CRS812
- qos-hw - remove unnecessary "offline" tx-manager for CRS812 (not supported by hardware)
- queue - improved system stability when using SFQ kind of queues
- route - added options in /routing/settings to adjust check-gateway=ping timers
- route - fixed SNMP output for ECMP routes having interface gateways
- route - hide suppress-hw-offload setting from devices that do not support it
- route - improved stability
- route - improved system stability with multicast routing
- route - make check-gateway=ping work on p2p interface gateways
- route - removed /routing stats mem-blocks
- routerboot - fixed boot MAC for CRS305-1G-4S+ and CRS328-4C-20S-4S+ switches ("/system routerboard upgrade" required)
- sfp - expose sfp-cmis-module-state to monitor
- sfp - filter out non-breakout modes for breakout modules
- sfp - fixed "sfp-tx-fault" state indication for CRS520-4XS-16XQ
- sfp - fixed combo-mode change for CRS326-4C+20G+2Q+
- sfp - fixed missing link up/down notifies
- sfp - improved initialization and linking for 25G DAC on CRS812
- sfp - improved system stability with some GPON modules for CRS418, CCR2004 and CCR2116 devices
- sfp - recognize 40G Active Cable (XLPPI)
- sfp - remove 40G-baseCR4, 40G-baseSR4-LR4 from sfp-supported list for qsfp28-x-3 interfaces
- snmp - added lldpLocChassisId OID
- snmp - count only "bound" leases for mtxrDHCPLeaseCount OID
- snmp - make lldpLocPortId and lldpLocPortDesc OIDs information consistent with LLDP TLVs
- socksify - improved system stability when using Socksify service
- ssh - added support for ED25519-SK keys
- ssh - improved logging of failed login attempts
- ssh - refactored SSH service internal processes
- ssh - renamed User SSH keys "key-owner" field to "info"
- ssh - replaced "always-allow-password-login" with "password-authentication" in SSH settings
- supout - added info log entry when autosupout.rif is generated
- switch - added dynamic "copy-to-cpu" ACL rule for loop-protect
- switch - automatically add local bridge MAC to switch FDB
- switch - fixed non-IP multicast packet receive on 98DX8208, 98DX8216, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255, 98CX8410 switches
- switch - improved HW bond load balancing by adding MPLS labels to transmit hash for 98DXxxxx, 98CXxxxx switches
- switch - improved stability on MediaTek switch chips
- swos - fixed "allow-from" setting for MIPSBE devices
- system - added disks to /system/resource/hardware list
- system - detect policy mismatch sooner if script is executed internally by some other service
- system - fixed local update package filename generation
- system - fixed network header offset for interfaces with MAC (fixes VRRP Tx on IGMP snooping bridge)
- system - fixed potential configuration loss when available disk space was insufficient
- system - fixed saving panic logs to autosupout.rif for ARM CRS3xx devices
- system - improved system stability when processing different kinds of lists
- system - improved system stability when processing GRE packets on TILE devices
- system - improved system stability
- system - limit number of interface-lists to 244
- tr069-client - added LTE link recovery timer setting
- tr069-client - allow disabling Device.WiFi.AccessPoint
- tr069-client - expose 5G NR signal metrics for the Chateau R17 ax
- traffic-generator - added support for injecting pcapng files
- undo - do not show internally issued commands in /system/history
- undo - show console commands in WinBox/WebFig for /system/history entries
- ups - fixed board hibernation shutdown
- usb - fixed cases where USB bus order could change on D53 devices
- usb - LTE modem and USB-Serial Controller enumeration fix
- usb - support video capture devices for arm64 and x86, for passthrough to containers
- user-manager - added RadSec support
- veth - add container-mac-address setting
- veth - added default print brief table mode
- veth - added dhcp setting that allows to auto-configure IPv4 address, works when VETH is bridged with other interfaces and there is a DHCP server running somewhere on that network
- veth - complain immediately when VETH gateway not reachable, more detailed error message when network setup fails
- veth - fixed IP address not appearing in the app menu when VETH uses DHCP
- veth - fixed VETH interface not getting an IP address in a vlan-aware bridge containing multiple DHCP servers
- veth - show only when container package installed
- vrf - added read-only property to IPv4/IPv6 addresses, ARP and IPv6 neighbor
- vrf - allow setting comment on default "lo" interface
- vrrp - do not show "ttl not 255" warning when received VRRP VRID does not match with configured VRID
- vrrp - fixed gratuitous ARP being sent after VRRP is disabled (fixes packet forwarding on HW offloaded bridge after VRRP is disabled)
- w60g - fixed possible memory leak when an interface is disabled
- webfig - added a hint for Undo/Redo buttons
- webfig - added Apps menu to login
- webfig - added capability to check/uncheck entry tree in skin designer
- webfig - added Copy capability
- webfig - added missing PPP types to Skin Designer
- webfig - added TCP State column for connection tracking table
- webfig - check if device is still reachable before disconnect on error
- webfig - fixed container config memory high input
- webfig - fixed issue where routes and PIM table did not load
- webfig - fixed issue where Torch stops running
- webfig - fixed name and title store in skins
- webfig - fixed new item window name when using skins
- webfig - improved mikrotik_logo.svg
- webfig - improved service stability after deleting a skin
- webfig - increase graph width for better scaling
- webfig - increase maximum number size in forms
- webfig - make close button as a button instead of link
- webfig - make combobox accessible to screen readers
- webfig - remember last user in login page
- webfig - turn off auto-capitalize and auto-correct for on-screen keyboards
- wifi - added "CAP" information field on interfaces view
- wifi - added CAPsMAN forwarding support (datapath.traffic-processing=on-capsman)
- wifi - added configuration parameters relevant to the upcoming WiFi 7 products
- wifi - enable configuration of "3gpp-info-raw" and "realms-raw" interworking parameters
- wifi - fixed issue when trying to use interface as bonding slave
- wifi - fixed multi-passphrase usage in combination with access-list
- wifi - fixed possible duplicate values for WPA3 authentication types in scan results
- wifi - fixed possible memory leak when failing to start AP on chosen channel
- wifi - fixed some CAPsMAN settings to be optional
- wifi - improved formatting of FT request action frames
- wifi - improved interface stability when encountering authentication failures
- wifi - improved stability when capturing data at high rates with wifi sniffer
- wifi - increased accounting interval, maximum client entry count for 2.4GHz probe response delay feature
- wifi - rename ft-wpa2-eap authentication type to "ft-eap"
- wifi - split access-list time property in days and time
- wifi-mediatek - added Superchannel regulatory profile
- wifi-qcom - added Unsolicited BSS Transition Management Request support
- wifi-qcom - improved default RTS/CTS policy for CPE station radios
- wifi-qcom - multicast-enhance will no longer apply for station mode configured devices
- wifi,wireless - include "Event-Timestamp" in RADIUS accounting messages
- winbox - added "Last Status" and "Last Address" fields in "Tools/Email" menu
- winbox - added file selector for BTH files
- winbox - added Forwarding Table in "MPLS" menu
- winbox - added missing "SM-DP+ Oid" LTE eSIM provisioning field
- winbox - added Sessions tab in "Routing/RPKI" menu
- winbox - added support for new settings and fixed several existing ones
- winbox - Bandwidth test, Speed test, Ping, Traceroute tools use RouterOS DNS service to resolve domain names
- winbox - fixed "Too many entries" not showing in WinBox v4
- winbox - fixed Disk iscsi/smb configuration
- winbox - fixed Disk NVMe-TCP configuration
- winbox - fixed Dude/Tools appearance after Apply action
- winbox - fixed graphs in some forms with big numbers
- winbox - fixed Keepalive Time format in "Routing/BGP" menus
- winbox - fixed Preshared Key "auto" and "none" options for WireGuard Peer
- winbox - fixed switch QoS monitor for mirror properties
- winbox - hide certificate "Issuer" field for certificate template
- winbox - hide IPv6 addresses for IP neighbors that no longer have them
- winbox - make multiple address fields required
- winbox - make separate inputs for WiFi Interworking "Authentication Types" and "Connection Capabilities" fields
- winbox - make VETH gateway fields not required
- winbox - move VRF from Ethernet to generic Interface table
- winbox - removed "Add" for dynamic DNS servers
- winbox - reorder BGP and OSPF tabs in logical order
- winbox - restore route max object 10000 limit
- winbox - show "Trusted" field for certificate template
- winbox - show warnings in "Routing/BGP" menus
- winbox - show warnings in Disk menu
- winbox - updated and shortened window titles (e.g. Address List -> Addresses)
- wireguard - added VRF option (CLI only)
- wireguard - allow to add AllowedIPs configuration for client configuration template
- wireless - added last-ip parameter for the CAPSMAN registration-table tab
- wireless - improved system stability when stopping scan process
- www - added option to disable individual web services in /ip/service/webserver and IP>Services>Web Server
- www - handle escaped characters in resource IDs and names for REST API requests
- www - process REST API requests only after user authentication is completed
- www - removed ability to publish directories via "/files" www service